SANDWELL profile Sander Model: SDT10/13-A2P1L2
This machine can be used for the processing of antique flooring.
By replacing different abrasives (such as wire brush, DuPont wire, sand wire, etc.), the sanding of antique drawing, white blank and paint board can be realized.
Greatly provide production efficiency, reduce manual operation.
Configuration description:
1. This machine is equipped with 6 sets of sanding units, which are composed of five sets of sanding components.
2. The first and second sets of sanding parts, two sets of horizontal spiral roll positive and negative sanding group sanding the transverse concave and convex surface of the workpiece, both sides can be sanded in place.
3. The third sanding component, two groups of sanding units, 360 degrees forward and 360 degrees reverse respectively, carry out all-round sanding and sanding on all corners of the workpiece.
4. Fourth and fifth sets of sanding parts, two groups of spiral roll sanding units, one positive and the other negative, large diameter roll sanding large area, the first several sanding lines are thoroughly sorted out. The concave and convex surfaces are sanded.
Excellent characteristics
1. This machine has good effect on abnormal surface grinding. It is the best choice to reduce labor intensity, reduce labor and improve productivity.
2. The system uses PLC to connect the high-definition touch-screen communication frequency converter, which shows, operates, adjusts, maintains and instructs directly, replaces a large number of trip switches with encoder, which makes the control more accurate, debugging more convenient, the failure rate lower and the maintenance cost lower.
3. Conveying and independent variable frequency speed regulation for each group. Various motors can be adjusted independently by frequency conversion and equipped with different abrasives to achieve different sanding effects. The operation is stable and can be used for different materials.
4. Floating sanding structure, fixed worktable, can be connected to the production line.
5. Rollers and working components can be adjusted independently, and the plate with deeper grooves can be sanded.
6. Sanding parts can be pulled out as a whole, Abrasives can be easily replaced. Patented fast-changing device is used for discs, and the operation is simple.
7. Vacuum absorption design is selected for the worktable, which is used for sanding narrow sheet.
Mechanical parameter description锛?br/>
Machine type:SDT10/13-A2P1L2
Maximum processing width50锝?000/1300 mm
Maximum processing height10锝?50 mm
Minimum processing length450 mm
Conveyor motor power1.5 kw
Integral lift motor power1 x 0.75 kw
Sand roller motor power1 x 1.1/1.5 kw
Horizontal Sand Main Motor2 x 1.1/1.5 kw
Disc motor power2 x 1.1/1.5 kw
Component fine-tuning motor power5 x 0.25 kw
Swing motor power5 x 0.25 kw
Feeding speed1-10 m/min
Rotary speed of sand roll100-280 r/min
Disk size3 x 9/11 x 蠁180
Sand roll size2x 蠁380 x 1000/1300 mm
Conveyor band width1000/1300 mm
Power requirements3/PE 380V 50Hz
Clean air pressure4~6Pa
Working table height845mm
Dust-collecting wind speed22m/s
Vacuum cleaner蠁125mm脳8
Total power supply13.28kw
Machine size4000 x 1800/2100 x 2000mm
Machine weight3000 kg
Causes of Common Failures and Solutions
1. No power display on operation panel
Cause split: 1. The power switch is not turned on.
Solution: Turn on the power switch.
Cause split: 2. Control cabinet switch off.
Solution: Check the circuit and close the switch.
2. Emergency stop alarm
Reason split: 1. The emergency stop button is pressed.
Solution: Remove the emergency stop button.
3. Lower limit alarm of main frame
Reasons split: 1. The main frame down to the end.
Solution: Raise the main frame.
The cross sand components
Functional features: The elastic belt supported by the brush is composed of a spiral flexible sanding unit, and the direction of rotation and the moving direction of the workpiece are 90 degrees. The left and right movements are moved at a constant speed, and the sanding intensity, depth and speed are all digitally adjusted. Stepless speed regulation. The mechanical structure is pulled out and the abrasive replacement is quite convenient. This part is mainly used for sanding and painting of paint and white billet for uneven workpieces with lateral ends. The depth of the depression is determined by the width of the abrasive.
The spiral sand roller.
Functional features: The elastic belt supported by the brush is composed of a spiral flexible sanding unit, and the rotation direction is parallel to the moving direction of the workpiece. The oscillation is oscillated from side to side, and the sanding intensity, depth and speed are all digitally adjusted. Stepless speed regulation. The mechanical structure is pulled out and the abrasive replacement is quite convenient. The large-diameter sand roller has increased contact with the workpiece to effectively increase the sanding effect. This part is mainly used for sanding and painting of paint and white billet for uneven workpieces with forward corners. The depth of the depression is determined by the width of the abrasive.
The disc part.
Functional features: The flexible sanding unit consisting of the elastic belt supported by the brush is mounted on a rotating flat disk, and the direction of rotation and the moving direction of the workpiece are 360 degrees. The oscillation is oscillated from side to side, and the sanding intensity, depth and speed are all digitally adjusted. Stepless speed regulation. The mechanical structure is pulled out, the whole unit is quickly and independently removed, and the abrasive replacement is quite convenient. This part is mainly used for sanding and polishing of paint and white billet for all rugged workpieces (called universal angle grinder). The depth of the depression is determined by the width of the abrasive.China Profile Sanding Machine
website:http://www.sandwell-sand.com/profile-sanding-machine/